Peanut Butter Fudge (Microwave Recipe, 4 Ingredients!) (2024)

FAQs

Why won t my microwave fudge set? ›

Fudge Didn't Set

If your fudge turned out super sticky, or it didn't set as it cooled, it probably never got hot enough. This mistake is super easy to avoid if you use a candy thermometer and cook the fudge to the temperature specified in the recipe (usually between 234 and 239°F).

How to Make Fudge. The trick to good homemade fudge is to cook the ingredients to the right temperature to form a sugar syrup, and cool the mixture properly so the texture of the fudge turns out smooth and firm, but soft enough to cut. Here's how to make fudge on your stovetop and in your microwave.

Place the peanut butter in the microwave, and heat it for 30 seconds. Once the 30 seconds is up, stir the peanut butter to makes sure it's melting evenly. Place the peanut butter back in the microwave for another 30 seconds, and stir again. This will probably take a few rounds to get to your desired consistency.

The main reason is that your Fudge has not reached the optimum temperature. If your mixture only reaches 110 or 112 degrees Celsius it will always be soft. That's why we recommend investing in a sugar thermometer. Another reason your Fudge is not setting is that the ratio of liquid to sugar is too high.

OPTION 4) If you think the reason it didn't set was because you didn't heat it to the right temperature, you could try putting it back into the pan and re-cooking.

Homemade Fudge Doesn't Always Set

If your fudge doesn't firm up after a few hours, you either have too high an amount of liquid to sugar, or your mixture hasn't reached the soft-ball stage. Using a candy thermometer can help home cooks avoid this problem.

Evaporated milk doesn't have sugar added. The sweetened condended milk is needed as no extra sugar is added to the fudge. If evaporated milk were used then the fudge would not be sweet enough and also would still be too soft unless the fudge is frozen.

The key to successful, nongrainy fudge is in the cooling, not the cooking. The recipe calls for heating the ingredients to the soft-ball stage, or 234° F, then allowing it to cool undisturbed to approximately 110° F.

There would be no problem if it was a glass jar, but plastic can melt and/or give off chemicals when heated. So, for plastic try putting it in a pot of hot tap water, instead.

What does microwaving peanut butter do? ›

Technically, you can melt a bowl of the latter, but the nuts will just get toasty instead of melting — so the choice is up to you. Either way, be sure to use your warm spread right away, since it will harden again as it cools down; although it'll taste so delicious, this likely won't be a problem.

You bet! Just be sure to place SKIPPY^® Peanut Butter in a microwave-safe container. SKIPPY^® Peanut Butter jars, however, can't go in the microwave or oven.

Temperature The fudge mixture may not have been heated enough. For most fudge recipes, the sugar needs to reach a soft ball stage (around 235-240°F) to set properly.

If your fudge is soft or runny, it probably didn't come up to a high enough temperature while it was cooking. Put it back into the saucepan and add 1–2 US tbsp (15–30 ml) of 35% fat whipping cream. Stir the fudge as it heats, but only until the sugar in the chocolate is completely melted again.

As water gradually evaporates, sugar is concentrated and the temperature of the mixture rises above 100°C (212°F). If there is too much evaporation, when the cooking time is too long, there will not be enough water left in the fudge and it will be too hard.

To fix it, you can reheat the fudge mixture over low heat and continue cooking until it reaches the proper temperature. Be sure to use a candy thermometer to monitor the temperature accurately. Alternatively, you can try to salvage chewy fudge by mixing it into ice cream or using it as a topping for desserts.

How do you fix fudge that is too soft? Bring the fudge back to a boil with 1–2 US tbsp (15–30 ml) of cream. If your fudge is soft or runny, it probably didn't come up to a high enough temperature while it was cooking. Put it back into the saucepan and add 1–2 US tbsp (15–30 ml) of 35% fat whipping cream.

For perfect fudge, the syrup should form a soft ball that can be picked up, but easily flattened. If the syrup is undercooked, drops of syrup will sink to the bottom of the glass in threads or simply dissolve. If the syrup is overcooked, the ball will be hard and difficult to flatten with your fingers.

Graining can be caused by stirring the fudge mixture during the cooling process or not adding enough fluid to dissolve the sugar. The trick to fixing graininess is to melt the sugar crystals to give them another chance at setting properly.